Google+

Lista de códigos de retorno y su significado. - MuchoCATIA

Buscar
Vaya al Contenido

Menu Principal:

Lista de códigos de retorno y su significado.

Teoría CATIA > Tratam. de la inform.
Está Vd en: home>>CATDUAentorno>> Lista de codigos de retorno.

 

Lista de Códigos de Retorno detectados por el "Data Upward Assistant"

objetivo   El Data Upward Assistant tiene la capacidad para comprobar la estructura de datos dentro de un CATProduct, CATPart, CATDrawing, CATAnalysis, CATMaterial, CATProcess, e incluso modificar dicha estructura de datos.
  Usted puede encontrar aquí la lista de todos los códigos de retorno que puede ser detectada por el Data Upward Assistant y una descripción.

El Data Upward Assistant es útil en las siguientes situaciones:

•   antes de la recuperación de datos externos,
•  cuando los ficheros provienen de una Release anterior de CATIA,
•   enlaces rotos al abrir CATProducts,
•   incidentes en los que la actualización de un componente (por ejemplo, actualización de Sketch),
•  en el panel Edit-Links aparece: algunos elementos se encuentran, pero no tienen referencias,
•  los problemas de rendimiento cuando se abre un CATProduct (debido a que algunos elementos han perdido sus link's).
info

Niveles de Prioridad.

Leyenda de los Niveles de Prioridad (significado de los numeros entre parentesis):
  (1):  Código de retorno de la prioridad Uno: La mejora efectuada puede conducir al borrado de datos.
  (2):  Código de retorno de la prioridad Dos: La mejora efectuada puede conducir a la modificación de los datos (sin borrar nada).
  (3): Código de retorno de la prioridad Tres: Error sin importancia. La acción de mejora no tiene gran impacto en los Datos.
  (*) Este símbolo significa que la regla no está ejecutada en un documento que viene de un sistema de PDM (ENOVIAVPM, ENOVIA LCA).

Lista de Códigos de retorno detectados.

1.- ObjectSpecsModeler:

DOC: documento vinculado (raíz contenedor).

    DOC_1 (2): non typed document in a link => Cleaner: Document typed in the link.
  DOC_3 (2): missing links => Cleaner: Link counter set up-to-date.
  DOC_4 (3): ghost links=> Cleaner: Link counter set up-to-date.
  DOC_5 (2): destroyed links => Cleaner: Re-build the missing link.
  DOC_6 (3): applicative containers are lost => Cleaner: Empty stream added.
  DOC_8 (3): Bad performance when opening a document due to an invalid link counter => Cleaner: The link that does not appear to end-user is deleted in table of inter-document links, the table is just compacted.
  DOC_9 (3): Update of a CATPart cannot be completed => Cleaner: Data contained in all federators are put into one federator and empty federators are deleted.
  DOC_11 (3): SendTo on a CATPart shows a link to an useless CATPart => Cleaner: meaningless repository, containing no Input or Inputs that are no more pointed, is deleted.
  DOC_12 (1): Cannot open a document => Cleaner: Delete corrupted storages.
  DOC_14 (1) : A document cannot be opened and some OSM ERROR such as OSM_RE001 are raised. => Cleaner: If it is a consectionplane container or a CATCollabCont container then it will be physically removed from the document
  DOC_15 (3) : Selection/Unselection is very slow. => Cleaner: Remove empty and useless containers

CAT: Catalog

    CAT_0 (2): feature catalog with no name => Cleaner: Deletion of the link to this catalog.

CCL: Componente de un Catálogo (Component Catalog)

    CCL_0 (3): description's name and Name keyword are different => Cleaner: The description is renamed.
  CCL_1 (3): same chapter appears with a name in the Specifications tree and with another name in the definition list => Cleaner: The chapter is renamed.
  CCL_2 (3) (*): When a chapter's keyword is deleted, some internal data remain in descriptions => Cleaner: Useless internal data are removed.
  CCL_4 (3): A description's keyword value may be unlinked with its chapter's keyword => Cleaner: The keyword value is re-linked with its keyword.
  CCL_5 (2): Chapters can not be viewed in the Catalog Editor => Cleaner: Missing description pointing to the chapter is created under the root chaper.
  CCL_6 (1): File/SendTo shows a Ghost link => Cleaner: Delete the corrupted feature with invalid reference on a startup.
  CCL_7 (1) : A Part Familly still exist even if all descriptions have been deleted. The synchronization fails => Cleaner: delete the reference after deleting the last related description.

EXT: Link externo.

    EXT_0 (3): Existe un vínculo a un documento señalando, en una extensions feature sin usar => Cleaner: Supresión del enlace; el documento debe ser actualizado.
  EXT_1 (3) : Un material se pierde al abrir un CATProduct => Cleaner: Combinar todos los datos que se encuentran en todas las extensiones en un solo contenedor (Body).
  EXT_2 (3): Ghost links when opening a CATProduct => Cleaner: The reference of an extension is not in the same document that the reference of its base feature (probably after a replace).

 

HIE: Hierarchy.

    HIE_3 (3): A product instance has too many sub-products => Cleaner: Deletion of the over sub-products and product instance is synchronized.
    HIE_5 (3): A change of reference is made during save as operation when a private component cannot find its reference and error DOC_3 may reappears => Cleaner: Error DOC_3 is fixed completely by first pass of CATDUA.
  HIE_6 (1): Impossible to update the model: some assembly data (constraints) are invalid. => Cleaner: Invalid connection deletion.

 

2.- Product Structure:

   BRK: Objeto roto.

    BRK_0 (1): broken objects not aggregated => Cleaner: Deletion of objects.

LIF: Product Lifecycle.

    LIF_2 (3)(*): objects not reachable starting from root-product => Cleaner: Deletion of objects.
  LIF_4 (3)(*): non-destroyed objects in CATProdCont container => Cleaner: Deletion of objects.
  LIF_7 (3)(*): non-destroyed connections in CATProdCont container => Cleaner: Deletion of objects.
  LIF_8 (3)(*): non-destroyed connectors in CATProdCont container => Cleaner: Deletion of objects.
  LIF_9 (3): non-destroyed product bag reps in CATProdCont container => Cleaner: Deletion of objects.
  LIF_12 (3): Ghost Link on another document => Cleaner: Unset _ToProxy attribute.
  LIF_13 (1): A Ghost Link appears in SendTo command => Cleaner: Delete an internal object (proxy) whith an invalid link to a document.

AGG: Aggregation.

    AGG_1 (1): aggregated object does not know its aggregating object => Cleaner: deletion of the aggregation.
  AGG_2 (2): Ghost links, Undeletable view, Copy Paste failure => Cleaner: Update of the aggregation link.
  AGG_3 (2): A link Father-Son between an instance and the product is deleted, which disables the destruction of the instance => Cleaner: Use the Spec service CATSpecSetFather to reset the link.
  AGG_4 (2): At flexibility of product, a Constraint is broken. Before flexibility, all was OK. => Cleaner: Connector is put again on right attribute of Product, and instanciated on all referencing documents.
  AGG_5 (1) : Ghost link in File/SendTo command from a CATPart => Cleaner: Deletion of the useless PUBLISHING features.

ATT: Rule Attribute.

    ATT_2 (3): unused attribute _UpdateError => Cleaner: Deletion of attribute.
  ATT_3 (1): unused attribute (activrep) valuated => Cleaner: Unset of the attributes.
  ATT_4 (2): update stamp incorrect on position attribute => Cleaner: Update of UpdateStamp.
  ATT_6 (2): an external reference is up-to-date whereas its target has changed. => Cleaner: Sets the link as Not UpToDate, and initializes the timestamp list.
  ATT_11 (1): Ghost links are visible through File/SendTo => Cleaner: Delete the overloaded attribute on the Product instance.
  ATT_12 (2): Problem of synchronisation of external Parameter pointing a Publication of Parameter => Cleaner: Keep only one pointing attribute valuated, with priority to the resolved one.
  ATT_13 (2): An External Reference is seen as Synchronized although referenced geometry has changed => Cleaner: Make the Connector not UpToDate, and Update it.
  ATT_14 (2) : A CATPart is seen as modified after being inserted in a CATProduct => Cleaner: Once UPD_2 cleaning is done, an additional action on Connectors is needed: synchronization status is reseted, in order to force their update.

UAQ: Product structure - Unexpected Attribute Quality.

    UAQ_1 (3): Quality on publication instance different from the publication startup => Cleaner: Change quality from neutral to in.

Ir arriba

UAV: Product structure - Unexpected Attribute Value.

    UAV_0 (2): illegal position attribute => Cleaner: Position is set to identity.
  UAV_1 (1): incorrect overloading for position attribute => Cleaner: Switch in flexible products.
  UAV_2 (3): component's list with blank => Cleaner: Deletion of blanks.
  UAV_3 (1): A constraint is not in the right container => Cleaner: deletion of the constraint.
  UAV_4 (3)(*): invalid object pointed by a connector => Cleaner: Link set correctly.
  UAV_5 (2)(*): connection instance and reference point different connectors (by publication) => Cleaner: Connection synchronized.
  UAV_6 (3): invalid connector pointed by a connection => Cleaner: Connection synchronized.
  UAV_7 (2): instance of Product with overloaded contextuality => Cleaner: Product instance synchronized.
  UAV_8 (2): a Product with many representations (no Visualization when opening) => Cleaner: Product instance synchronized.
  UAV_9 (3): connector with incorrect connections => Cleaner: incorrect connections deleted.
  UAV_10 (3)(*): A part document is pointing at useless components => Cleaner: empty the _component attribute.
  UAV_11 (3)(*): The attribute Shape Connector of the connector is pointing an invalid document => Cleaner: Reset the attribute Shape connector.
  UAV_12 (3)(*): The attribute _TechnoLinkAttr is wrong => Cleaner: Reset the attribute _TechnoLinkAttr.
  UAV_14 (3): Same publication appears several times in the Specification tree => Cleaner: Remove all identical publications but one.
  UAV_15 (2) (*): The PUBLISHING_Pointage, PUBLISHING_Etiquette and/or PUBLISHING_PubName attributes, are affected on Instance instead of reference => Cleaner: Transfer the PUBLISHING_Pointage, PUBLISHING_Etiquette and PUBLISHING_PubName attributes from instance level to reference level.
  UAV_16 (2): Instance externals are locally set => Cleaner: Reset instance externals.
  UAV_18 (2) (*): No shape representation on a part reference or the shape representation on a reference points to another part's shape => Cleaner: The shape representation points to the own shape of the part.
  UAV_19 (2) (*): A Contextual Link is always Not UpToDate, even after an Update => Cleaner: The ContextualLink pointing is unset.
  UAV_20 (2): Error pannel on PRDCONNECTION displayed when updating the assembly => Cleaner: Compares the PrdConnection attributes to its direct reference, and resets the corrupted attributes according to the value held by this reference.
  UAV_21 (1) (*): The number of publication of the part in the assembly count less than the number of publication in the part when opened separately => Cleaner: resets the corrupted list of publication according to the value held by this reference.
  UAV_22 (1): Error occurs during Update operation => Cleaner: Deletion of an invalid reference Connection.
  UAV_23 (2) (*): A publication is wrongly seen as up to date => Cleaner: Updates the Time Stamp of the Parameter in case of a Publication pointing to a Parameter.
  UAV_27 (2): Impossible to select a Publication under a Product Instance => Cleaner: Launch a SmartSynchro from the Publication reference and restore the association.
  UAV_29 (2) : Publications pointing a parameter are no longer resolved => Cleaner: Publications using an old protocol are re-valuated using the new one
  UAV_30 (1) : Connections are lost in an product assembly that has been made flexible => Cleaner: all connection instances of connections which reference has already been instantiated are removed.
  UAV_31 (2) : A contextual link is seen as connected (OK) in the " Define contextual Links" command whereas it is not possible to resolve it and update the contextual geometry ! => Cleaner: Fix the PRDCTXINPUT feature so that it points the same context (that is to say Product instance) as the one pointed by its PRDCTXREPO.
  UAV_32 (2) : When parameter value is changed, publication may show a wrong update status and be seen as up to date => Cleaner: Set the Time Stamp of the Parameter under the Publication attribute (_ModifiersTS) in case of a Publication pointing to a Parameter.
  UAV_33 (2) : Some publications cannot be remove. No action is possible on such publications => Cleaner: Deletion of useless publications.
  UAV_34 (2) : A Part Number conflict exists in assembly => Cleaner: Automatically detects the Part Number conflict and renames accordingly
  UAV_35 (2) : When insert a part in product, the part goes into hide mode => Cleaner: Resets the show atribute to CATShowAttr and Part got modified.

UPG: Upgrade.

    UPG_0 (3): invalid multi-representation (V5R2 model) => Cleaner: Upgrade of multi-representation.
  UPG_1 (3) (*): After reordering the publications or deleting Part, the publications reference a wrong geometry => Cleaner: Upgrade this attribute by a new Spec relation without relative mode.

DOC: Linked Document (container root).

    DOC_7 (2)(*): no save link to a sub-product => Cleaner: Link switch as a save-link.

SYN: Synchronization.

    SYN_1 (3): Multi-Instantiation of one reference by synchronization. => Cleaner: deletion of the feature.
  SYN_2 (1): The PRDBAGREP attribute of the ASMPRODUCT does not reference the PRDBAGREP of the reference ASMPRODUCT. => Cleaner: reset the BagRepsList attribute of the ASMPRODUCT.

HIE: Hierarchy.

    HIE_4 (1) (*): An internal object (connector) has an inconsistent state and retains an instance-reference link to a useless document => Cleaner: Remove the offending connector.

NUM: Numbering.

    NUM_0 (3) (*): A warning pop-up is displayed when opening a CATProduct => Cleaner: Remove the phantom numbering.

Ir arriba

3.- Mechanical Modeler

BST: BackUp Start Up.

    BST_1 (3): BackUp StartUp not declared on CAA mechanical feature => Cleaner: BackUp StartUp is declared.

LIF: Product Lifecycle.

    LIF_1 (1): The size of the CATPart is abnormally huge comparatively to the number of elements and unused elements (Geometrical feature) are present => Cleaner: Deletion of unused elements, the Part is the same but smaller.
  LIF_3 (3): No visibility except the size of the CATProduct document (constraints deletion cases) => cleaner: Deletion of unused elements; the document is the same but smaller.
  LIF_5 (3)(*): non-referenced elements in the container CATSelSetsCont => Cleaner: Deletion of elements.
  LIF_10 (3)(*): not pointed or useless proxy objects => Cleaner: Deletion of the useless proxy objects.
  LIF_11 (3)(*): internal object unused in applicative container => Cleaner: Deletion of the useless objects.

MMR: Mechanical Modeler.

    MMR_0 (1): corruption of the 3 reference planes => Cleaner: Restore valid reference planes.
  MMR_1 (2): ShapeRep not pointed by a Product => Cleaner: Reset link.
  MMR_2 (2): No Maintool in the Part => Cleaner: Creation of a default Maintool.
  MMR_4 (2): Visualization misbehaviors and unexpected restrictions to the capabilities to move an instance elsewhere in the Mechanical Part. => Cleaner: reorder or create missing set under the Mechanical Part.
  MMR_5 (2) : No in work object in the tree or incorrect visualization => Cleaner: sets the PartBody as in work object

MMV:

    MMV_1 (3): Invalid graphic property on the part => Cleaner : Deletion of the invalid property.
  MMV_2 (3): Invalid graphic property remain in the model even after removal => Cleaner : Restore correctly the dress-up properties.
  MMV_3 (3): Wrong attribute values were streamed on the PartBody of a CATPart created on V5R10 level => Cleaner: Erase the wrong attribute names.

MGN: Mechanical Generic Naming (topology).

    MGN_0 (2): more than one topological result => Cleaner: Deletion of over results.
  MGN_3 (2): invalid update state on a feature => Cleaner: Restore a valid state.
  MGN_4 (3): the generic naming of the BRep features duplicates data => Cleaner: Remove the duplicated data.
  MGN_5 (3): Useless synchronization data remain on a feature => Cleaner: Remove the useless synchronization data.
  MGN_6 (1): Size of a CATPart on disk is abnormally huge => Cleaner: Remove useless Mechanical modeler data.
  MGN_7 (2) : Some cells of Datum Feature are not selectionnable => Cleaner: Add a namming to the cells
  MGN_8 (1): Setting Applicative Attributes and colors using dedicated CAA interface is long => Cleaner: Delete invalid BRep features for colors and applicative attributes.
  MGN_9 (1): CATDUA (LIF_1) borrar las Publicaciones en el Part en Feature BRep => Cleaner: borrar objeto BRep no válido y volver a apuntar la publication en un acceso al BRep que lo sustituya.(CATDUA (LIF_1) deletes publication in the Part on not aggregated Feature BRep => Cleaner: delete invalid BRep features and re-plug the publication on equivalent BRep Access.)
  MGN_10 (3): Bad performances during the update of a part containing big import features => Cleaner: Delete useles data.
  MGN_11 (2) : Some Feature Brep on Axis, Plane and Extremity created before R11 may be in update error but no error is generated. So they are pointing old no more existing geometry. => Cleaner: This Feature Brep are put in an no-updated state and the update will generate an update error allowing the correction of the FB.
  MGN_12 (3) : The size of the document is too big => Cleaner: Compress Feature Brep in order to minimize the size.
  MGN_13 (2) : Some Feature Brep are in Error => Cleaner: We try to retrive the lost specification, if not recovered a manual selection will be necessary.

MTR: Mechanical Tools.

    MTR_0 (2): tool's result not properly plugged => Cleaner: Result plugged.
  MTR_1 (3)(*): Body's reference is lost => Cleaner: Reference is set to Start-Up.
  MTR_2 (2): Shape Features not properly plugged => Cleaner: Re-plug of the Shape Feature.
  MTR_3 (3): invalid valuation of VisuOnOff attribute => Cleaner: Reset attribute.

MFT: Formas de las herramientas.

    MFT_0 (2): active/inactive status mismatched regardless to attribute structure => Cleaner: Reset attribute.
  MFT_1 (1): inactive Feature storing the result of the previous feature => Cleaner: No more result in the feature.
  MFT_2 (1): result of a shape feature valuated with result of the previous active shape feature => Cleaner: Result regenerated.
  MFT_3 (1): inactive Shape Feature does not have its attribute saved or it is unset => Cleaner: Attribute regenerated and/or re-evaluated.

GST: Generative Surface Tool.

    GST_0 (2): the user opens a CATPart with an unidentified object (broken icon) called RollingOffset; startup lost for a GSMRolingOffset => Cleaner: Re-plug the startup.

GSDGenerative Shape Design.

    GSD_0 (3): unused aggregated feature => Cleaner: Deletion of these useless features.
  GSD_1 (1): reference planes are set as datum or independent spec => Cleaner: Correction of the Visu Graph attribute, aggregation of of the moved reference plane in current OpenBody and creation of a new reference plane.
  GSD_2 (2): Update a CATPart, but orientation may be inverted => Cleaner: axis system attribute is modified in respect with new algorithm.
  GSD_4 (2): Ghost link exists in the CATPart => Cleaner: remove the link.

Ir arriba

CTX: Context.

    CTX_1 (3)(*): multi-contextuality for a Part => Cleaner: Deletion of over contexts.

CST: Constraints.

    CST_1 (2): non-typed constraint => Cleaner: The constraint is typed.
  CST_2 (2): attributes quality mismatched => Cleaner: Quality modification.
  CST_3 (1): not valuated mandatory attributes on constraints => Cleaner: Deletion of constraints.
  CST_4 (1): Ghost Link on a CATDrawing document due to an invalid "blocs" attribute of a constraint => Cleaner: Valuate the "blocs" attributes of the constraint.

UDF: User Feature.

    UDF_0 (2)(*): user-feature with an invalid input => Cleaner: Re-plug of inputs.

 

4.- Assembly:

ASD: Assembly Design (constraints).

    ASD_0 (1): the start up of constraint is not found. => Cleaner: Load the AsmCst.feat catalog.
  ASD_1 (1): isolated constraint => Cleaner: Deletion of constraints.
  ASD_2 (1): mismatched storage of constraint => Cleaner: Deletion of constraints.
  ASD_3 (2): The type of a constraint is lost => Cleaner: Restore the type of the constraint.
  ASD_4 (2): attributes quality mismatched => Cleaner: Modification of the quality.
  ASD_5 (1): inconsistency between the feature catalog in V5R12 GA and the catalog in later versions or service packs => Cleaner: Corrupted Fix Together is deleted and replaced by a new Fix Together.
  ASD_6 (1): a Fix Together without parent => Cleaner: Corrupted Fix Together is deleted.
  ASD_7 (2): An attribute of a constraint contains a wrong value => Cleaner: Set the right value to the attribute of the constraint.
  ASD_8 (3): Activity of the FixTogether is not displayed in F(x) => Cleaner: Valuate the Activity parameter of the FixTogether.
  ASD_9 (3): Impossible to reorder constraints, due to old and no more used sets => Cleaner: Delete of the old sets and the set of constraints that are not used anymore.
  ASD_10 (2): Some constraints can be seen in the 3D window, but they do not appear in the specifications tree => Cleaner: Aggregation problem: the CONNECTION does not know the ConstraintASM, but the ConstraintASM knows that the CONNECTION is its parent.
  ASD_11 (1): unusable constraints, which cannot be deleted => Cleaner: Delete corrupted constraints.
  ASD_12 (3): Some constraints are not visible in the Specification tree => Cleaner: "under construction".
  ASD_13 (3) : Save as Frozen (only one product)

AFI: Assembly Feature.

    AFI_1 (3): assembly feature pointing wrong inputs => Cleaner: Correction of wrong links "assembly feature->input".
  AFI_2 (2) (*): An instance of a Reuse Pattern feature was pointing into a wrong document, probably because of a problem during feature synchronization => Cleaner: Unset the pointing attribute on the instance.
  AFI_3 (3) (*): Ghost links appear in File/SendTo command from the CATProduct => Cleaner: Plug the instance to the right reference and Reset/Synchronize it.

 

5.- Analysis:

SAF: Features (Spec view).

    SAF_2 (2): feature has no explicit image => Cleaner: Creation of an explicit image.
  SAF_3 (1): feature contains invalid explicit data => Cleaner: Deletion of this data.
  SAF_5 (2): nodes with wrong activity status => Cleaner: Correction of the status.
  SAF_4 (2): Missing links between mesh and physical data attach on mesh => Cleaner: Creation of the appropriate links.
  SAF_5 (2): nodes with wrong activity status => Cleaner: Correction of the status.
  SAF_6 (2) : Assert when working with assembly model => Cleaner: Create missing feature data to be in accordance.
  SAF_7 (2) : Model cannot be solved nor saved => Cleaner: Explicit entities with duplicate tag number are detected and their tag number is corrected

 

6.- Sketcher:

SCS: Sketcher Constraint.

    SCS_0 (2): Sketch solving result is not stable. Geometries can move when the user edits a sketch => Cleaner: Add a missing "Help" parameter to sketcher constraint.
  SCS_1 (2) : There are ghost links on 2D Constraints. Attributes of 2D Constraints reference external documents => Cleaner: Suppress the invalid reference to the pointed document

SKT: Sketcher.

    SKT_0 (1): sketch with no father => Cleaner: Deletion of Sketch.
  SKT_24 (3): Fsur of the _FtrList must be referenced => Cleaner: Deletion of the Fsur.
  SKT_25 (3): mismatched version on sketch => Cleaner: Change version.
  SKT_26 (2): Ghost Link window when opening a CATPart => Cleaner: Re-plug the geometry with ghost links on their details/dittos in the CATDrawing to their startups in current CATPart document.
  SKT_27 (2): Output features are badly aggregated => Cleaner: The outputs are replaced under the dedicated node under the sketch they belong to.

SMG: SolveManager (Sketch object).

    SMG_4 (2): ImportedGeom attribute size must be the same as the number of operators => Cleaner: Resize list.
  SMG_5 (2): ImportedGeom attribute with no operator => Cleaner: Reevaluation of attribute.
  SMG_6 (2): mismatched ImportedGeometry attribute => Cleaner: Devaluation of attribute.
  SMG_9 (2): invalid number of constraints => Cleaner: Re-evaluation of attribute.
  SMG_16 (2): non-impacted Solve Manager at update => Cleaner: Set constraint attribute to neutral.
  SMG_17 (2): invalid OutputGeoms attribute => Cleaner: Revaluation of attribute.

IGS: Imported Geometrical Set.

    IGS_0 (3): invalid phantom operator => Cleaner: Deletion of the operator.

SKS: Sketch Support.

    SKS_0 (2): cannot use sketch absolute or a sub-element of a sketch absolute axis to create a feature => Cleaner: CATDUA puts absolute axis feature out of date.
  SKS_1 (2): Update cycle not detected => Cleaner: Change structure of feature to detect cycle.
  SKS_2 (2) : O point, H and V vectors of the absolute axis of the sketch are missing from the specification tree and are not visualized => Cleaner: Recreate the missing elements of the absolute axis of the sketch.

CRV: Curve.

    CRV_0 (2): end points not found on the curve => Cleaner: Add limit points.
  CRV_1 (3): Update result is not right because update propagation is wrong. => Cleaner: Attributes of several features are set to sp_NEUTRAL instead of sp_IN.
  CRV_2 (2): A Ghost link is visible in SendTo command => Cleaner: Set invalid "Start Point" attribute and "End Point" attribute with new limit points.
  CRV_3 (2): A Ghost link is visible in File/SendTo command => Cleaner:
  CRV_4 (2) : A circle seen as visible on previous application releases is now seen as invisible on this current release => Cleaner: The open curve is forced to be closed.
  CRV_5 (1) : An ellipse seen as invisible on previous application releases is now seen as visible => Cleaner: The ellipse which was previously invisible is deleted.

 

7.- Material:Ir arriba

MAT: Material.

    MAT_1 (1): more than one material container in a Part => Cleaner: Deletion of over containers.
  MAT_2 (3): orphans elements in the material container => Cleaner: Deletion of orphans.
  MAT_3 (2): wrong visualization of a material => Cleaner: Reapply of material. Note that this error could sometimes be impossible to repair if the material can not be retrieved (for example, if the material is located in an inaccessible material catalog).
  MAT_4 (3): invalid material link => Cleaner: Deletion of link.
  MAT_5 (2): material parameter contains wrong data => Cleaner: Modify the material parameter.
  MAT_6 (2): Ghost link on a material => Cleaner: Modify the link to a correct material link.
  MAT_7 (3): A blank line is displayed in the window of the "Send/To" command (ghost link) => Cleaner: A material is located in a wrong container (not the material container). This can lead to ghost links. This material is unused and should be destroyed.
  MAT_8 (2) : Ghost links in File/SendTo command => Cleaner: Advanced materials are corrected.

8.- Drafting:

DAS: Drafting Axis System.

    DAS_0 (1): Unrelated document can be pointed by the drawing document (it appears using Send To). => Cleaner: An object managing view axis origin has an invalid link to a 3D document.

DBA:

    DBA_0 (2): bad link on a default feature => Cleaner: Deletion of the link.

DDU: Drafting Dress-up.

    DDU_0 (2): Useless data (connector, 3D feature) is erroneously referencing another document (CATPart)  => Cleaner: Remove this data and thus its links pointing other documents.
  DDU_1 (2): Open a Drafting document displays a panel with an invalid link to another drawing => Cleaner: Remove the invalid links.
  DDU_2 (1): Ghost link on a CATDrawing document => Cleaner: Deletion of the axis lines, center lines or thread that are directly under the DrwCont container.

DOB: Drafting Operator Breakout.

    DOB_0 (1): A CATDrawing containing isolated views has still some links to 3D parts/product. This is detected when using File/SendTo => Cleaner: Deletion of the link.

DOP: Drafting Operator Projection.

    DOP_0 (1): A CATDrawing containing isolated views still has some links to 3D parts/product. This is detected when using File/SendTo => Cleaner: Deletion of the link.

DOS: Drafting Operator Section.

    DOS_0 (1): Unrelated document can be pointed by the drawing document (it appears using Send To). => Cleaner: A section operator has an invalid link.
  DOS_1 (1): A section operator is not aggregated => Cleaner: Deletion of the object.

GME: Generative Modeler.

    GME_0 (1): Unrelated document can be pointed by the drawing document (it appears using Send To). => Cleaner: Deletion of the object.
  GME_1 (1): Unrelated document can be pointed by the drawing document (it appears using Send To). => Cleaner: Deletion of the invalid link.

 

DRW: Drawing.

    DRW_0 (1)(*): more than one drawing in the document => Cleaner: Deletion of unused drawings.
  DRW_1 (1): Ghost links might be visible in a part document via edit links, or the size of a Part document might be strangely big => Cleaner: A DrwDrawing with external links is inside the CATPrtCont. It is not visible in the specstree.

DWE: Generative Drafting.

    DWE_0 (1): An object, managing links between the views and 3D document, points an unrelated document => Cleaner: Deletion of the useless object.
  DWE_1 (3) : A difference occurs between the number of linked documents in File/Desk compared to File/SendTo => Cleaner: Flag the view as not up-to-date and reports that an update is required to fulfill the cleaning operation.

DWS: Drawing Sheet.

    DWS_0 (2): views not well organized in a sheet => Cleaner: Re-ordinate views.
  DWS_1 (1)(*): corrupted sheet => Cleaner: Deletion of sheet.

 

DWV: Drawing View.

    DWV_0 (1)(*): corrupted view (not well aggregated) => Cleaner: Deletion of the view.
  DWV_1 (2): a View is linked with another Drawing => Cleaner: Deletion of the link.
  DWV_2 (2) (*): A warning pop up is displayed when opening a CATProduct => Cleaner: unplug a View sub-components with ghost links from their "ghost" reference and re-plug them to their startups in current document.
  DWV_3 (3): The local transformations of geometries in views (like translations, scaling, rotations, offset) do not work, usually when some 2D Component instances have been exploded or exposed in the CATDrawing. => Cleaner: The geometrical result of the axis component of a view has been lost.
  DWV_4 (3): The sketch support is in the no-show space => Cleaner: The sketch support is put in the show-space and its axis elements are put in the no-show space.
  DWV_5 (3) (*): Ghost links appear in File/SendTo command from a CATDrawing => Cleaner: Remove the invalid link.
  DWV_6 (3): The file size for CATDrawing or CATPart containing some 2DLayoutData is unexpectedly important => Cleaner: Useless Geometrical results are removed from CGM container data.
  DWV_7 (1) : Some circles seen as visible on previous application releases (V5R12) are now seen as invisible, or some ellipses seen as invisible on previous application releases (V5R12) are now seen as visible => Cleaner: Open circles are forced to be closed , and are visible again. Ellipses with detected problem are deleted.

 

DVM: Drawing View MakeUp.

    DVM_0 (2): unused View MakeUp => Cleaner: Deletion of View MakeUp

DWR: Drawing Relation.

    DWR_0 (3): incoherent relation has been detected => Cleaner: Deletion of the useless DrwRelation

DWT: Drawing Pattern.

    DWT_1 (3): not aggregated pattern has been detected => Cleaner: Deletion of the pattern.

GDI:

    GDI_0 (1) : A difference occurs  between the number of linked documents in File/Desk compared to File/SendTo => Cleaner: Deletion of the feature

GIE: Generated Item.

    GIE_0 (2): unused GenItem => Cleaner: Deletion of GenItem.

DAF: Drawing Area Fill.

    DAF_0 (3): Area Fill without profile => Cleaner: Deletion of area.
  DAF_1 (3)(*): Area Fill not aggregated => Cleaner: Deletion of area
  DAF_2 (3)(*): Area Fill with a missing curve => Cleaner: Deletion of area.
  DAF_3 (3): Area Fill without pattern => Cleaner: Apply default pattern.
  DAF_4 (1): A document contains AreaFills with ghost links to other documents => Cleaner: Delete these AreaFills.

HLV: HLr View.

    HLV_0 (1) (*): A generative view is not aggregated => Cleaner: Deletion of the object.
  HLV_1 (1) (*): The drawing document size can be out of propotion regarding the useful data contained inside => Cleaner: Deletion of the non aggregated generative view
  HLV_2 (1) : A Ghost Link is displayed in File/SendTo command => Cleaner: delete the link.
  HLV_3 (1) : A Ghost Link is displayed in File/SendTo command => Cleaner: delete the link.
  HLV_4 (1) : A Ghost Link is displayed in File/SendTo command => Cleaner: delete the link.
  HLV_5 (3) : Associativity is lost for definition of Breakout profile, section view profile, section-cut profile, auxiliary profile or modification of graphic properties or delete of GeneratedItems. => Cleaner: No clean available. For auxiliary view, Section(-cut) edit and replace the profile, and for breakout remove and re-draw it.

STD: Standards.

    STD_0 (2): too many standards in the document => Cleaner: Deletion of unused standards.
  STD_1 (2): Standard not synchronized with the active sheet => Cleaner: Re-synchronization of standards.

Ir arriba

DET: Drawing Detail (2D component).

    DET_0 (3)(*): 2D Component not aggregated => Cleaner: Deletion of component.
  DET_1 (3)(*): 2D Component not typed through interface => Cleaner: Deletion of component.
  DET_2 (2)(*): 2D Component instance has its reference outside its document => Cleaner: 2D component reference is created inside the same document and replace the wrong one.
  DET_3 (1): 2D Component instance has too big or too small scale => Cleaner: Deletion of the scale.
  DET_4 (2) (*): redundant local reference exists in the model => Cleaner: Instances of the redundant local reference are redirected to the good one and the redundant local reference is deleted.
  DET_6 (1): Unpredictable behavior when using a drafting detail/ditto => Cleaner: invalid 2D component instance is deleted.
  DET_7 (2) (*): Open a CATDrawing displays a panel with an invalid link => Cleaner: unplugg the View sub-components with ghost links from their "ghost" reference and replug them to their startups in current document.
  DET_8 (2): Some ghost links are detected when trying to use "Send to" command, when some 2D Component instances are present in the CATDrawing document => Cleaner : The link is modified so that it points to the correct internal object.

OLE: OLE Object.

    OLE_0 (2)(*): OLE object pointing at an invalid drawing => Cleaner: the OLE object is replaced by a new one.
  OLE_1 (1) : A ghost link can be detected with File/SendTo => Cleaner: A useless OLE feature is removed

DWG: Generative Dimension.

    DWG_0 (1): object managing dimension generation no more used => Cleaner: Deletion of GenDim.
  DWG_1 (3): object managing dimension generation not aggregated => Cleaner: Deletion of GenDim.

DWC: Callout.

    DWC_1 (3): Callout not aggregated => Cleaner: Deletion of Callout.
  DWC_2 (2) : Callout arrows are visible eventhough the show attribute is set to CATNoShowAttr. => Cleaner: re-set the show attribute to CATShowAttr.

DWA: Projected Axis.

    DWA_1 (3): object manufacturing cut-views not aggregated => Cleaner: Deletion of Projected Axis.

DWH: Generative pattern.

    DWH_1 (3): generative pattern not aggregated => Cleaner: Deletion of Generative pattern.

DWP: Pattern Mapping Table.

    DWP_0 (3): pointer for pattern on 3D no more used => Cleaner: Deletion of object.
  DWP_1 (1): pointer for pattern on 3D not aggregated => Cleaner: Deletion of object.

DAO:

    DAO_0 (3)(*): Associativity pointing an external link with the document => Cleaner: Deletion of Associativity.
  DAO_1 (3)(*): Ghost Link due to useless drafting data referencing another document => Cleaner: Deletion of useless data and its link.
  DAO_2 (2) : Extension line is not visible (or not correctly) when creating extension line for roughness => Cleaner: View scale is taken into account for associative position dimensions extension line (overrun).

PIC: Drawing Picture.

    PIC_0 (3): Non aggregated Picture => Cleaner: Deletion of the picture.
  PIC_1 (2): At CATDrawing openness, reframe on is infinite => Cleaner: Modification of picture position value (set at 0;0) and moved to no-show space.

VWN: VieWName.

    VWN_0 (1): Ghost links are visible through File Send to => Cleaner: The formula is deleted then rebuilt so that there are no external parameters.

GPT: Generative Point.

    GPT_0 (1): Unrelated document can be pointed by the drawing document (it appears using Send To) => Cleaner: Deletion of the object.

SAC:

    SAC_2 (1): Ghost links appear in the File / SendTo command from a CATAnalysis => Cleaner: Remove Analysis Connector containing a Ghost Link.

LVW: Layout View.

    LVW_1 (2): File / Send to Command shows a Ghost Link => Cleaner: The "View Filter" attribute of View2DL with an external link is unset.

DFM: Drafting Format.

    DFM_0 (2): When opening a document which was created with a previous version, the format of some sheets is flipped => Cleaner: compute and set new values for invalid attributes.

LPR: L01 Product Profile.

    LPR_1 (1): When deleting a specific Profile, other Profile2DL are seen as not up-to-date => Cleaner: The "ViewFilter" attribute of View2DL with an external link is unset.

9.- Annotation:

Ir arriba

DST: Simple Text.

    DST_0 (1): invalid simple text => Cleaner: Deletion of the text.
  DST_1 (1) (*) : A ghost link appears in old drawing containing a section view. => Cleaner: Removes the link but keeps the text as it was.
  DST_2 (1): The number of annotations based on simple text found by search command is higher than the number of annotations based on simple text seen by the user => Cleaner: Deletion of each annotation based on simple text which is not visualized in the view.
  DST_3 (3) : Display of an annotation is not correct. => Cleaner: The display of the annotation is modified to match the font size specification.

DCR: Connector.

    DCR_0 (2): problem on connector => Cleaner: Retrieve section specification in related view.
  DCR_1 (3)(*): obsolete internal element for associativity => Cleaner: Deletion of object.
  DCR_2 (1): Broken dimension or ghost link on a CATPart in Send To command => Cleaner: Information of associative dress-up (dimension, annotation, constraint,...) for assembly positioning has been lost.
  DCR_3 (1): A link to a 3D connector has not been deleted after isolate => Cleaner: Deletion of each 3D connector which can be found in an interactive view.
  DCR_4 (3): Unnecessary big drawing document => Cleaner: Deletion of useless element.
  DCR_5 (1) (*): The "Send to" command shows that a drawing is linked to another drawing => Cleaner: Deletion of this link.
  DCR_6 (1): The "Send to" command shows that a drawing is linked to another drawing => Cleaner: Deletion of this link.
  DCR_7 (2): Ghostlink appears in document pointing to a CATPart => Cleaner: Update of the link.

DCS: Drafting Constraint.

    DCS_1 (2): Constraints, which are not correctly aggregated, are not taken into account => Cleaner: Change the place where the constraints are aggregated.
  DCS_2 (2) : Some annotations are displayed with wrong status and colors due to an internal corrupted object. => Cleaner: Link between Connector and View aggregating the constraint is repaired.

DCT: Container.

    DCT_0 (1): Data model with the V4 format became useless but are nevertheless still stored => Cleaner: Delete the useless data
  DCT_1 (2): Bad display of fonts, diameter symbol or no visualization of datum feature => Cleaner: Create a missing feature for the annotations' visualization.
  DCT_2 (1) (*): Ghost links appear in Send to command due to non aggregated feature => Cleaner: Delete the non aggregated feature.
  DCT_3 (2): Dimensions and some annotations can not be built in the 2DL or FTA workbench on the given document. Some of the existing objects are not updated normally => Cleaner: Reinitialize defective containers.
  DCT_4 (3): An error panel is triggered when opening the document saying that a used font is not available although this font is not used by any annotation => Cleaner: The reference to the font is removed from the document.
  DCT_5 (2) : It is impossible to use new fonts on dimensions inside the document => Cleaner: Remove unsed fonts from the list + add space in the list if needed.

DDI: Dimension.

    DDI_0 (2): invalid dimension pointing data => Cleaner: Deletion of the dimension.
  DDI_1 (1)(*): dimensions pointing in another document => Cleaner: Deletion of the dimension.
  DDI_2 (1)(*): constraint data corrupted => Cleaner: Deletion of the dimension.
  DDI_3 (3): non aggregated dimension => Cleaner: Deletion of the dimension.
  DDI_4 (2): The dimension display does not match dimension properties => Cleaner: Update dimension properties.
  DDI_5 (1): The number of dimension found by search command is higher than the number of dimension seen by the user => Cleaner: Deletion of each dimension which is not visualized in the View.
  DDI_6 (1): a Ghost link appears in File / SendTo => Cleaner: Deletion of the external link.
  DDI_7 (1): a Ghost link appears in File / SendTo => Cleaner: Deletion of the external link.
  DDI_8 (1): A panel is displayed when opening a CATDrawing => Cleaner: Deletion of an invalid link.
  DDI_9 (1): A panel is displayed when opening a CATDrawing => Cleaner: Deletion of an invalid link.
  DDI_10 (2): Some radius dimensions have a wrong display => Cleaner: Invalid symbol mode is set to Automatic.
  DDI_11 (2) : The dimension text doesn't use the right font => Cleaner: The dimension visualization is rebuilt.
  DDI_13 (2) : The dimension model is defining some extension line interruptions which are not displayed. => Cleaner: The guilty dimensions are rebuilt for visualization.

DAC: Drawing Area cotation.

    DAC_0 (1)(*): invalid dimension line => Cleaner: Deletion of the dimension.
  DAC_1 (1): The number of graphical dimensions found by search command is higher than the number of graphical dimensions seen by the user => Cleaner: Deletion of each graphical dimension which is not visualized in the view.
  DAC_2 (1): Annotation are not seen in the drawing but while printing the same annotation is seen with a heigth equal to 10 => Cleaner: Deletion of the annotation.
  DAC_4 (2) : Changing standard by Page Setup causes a Roughness Symbol reversed => Cleaner: Restore a correct orientation link.

DCH:

    DCH_0 (1): Invalid 3D-Connector referred in constraint => Cleaner: Deletion of the constraint.
  DCH_1 (2): Invalid elements on a constraint => Cleaner: Constraint is fixed.
  DCH_2 (2) (*): Send to command shows that an isolated view is still linked to its part => Cleaner: Deletion of each hybrid constraints which can be found in an interactive view.

DTE:

    DTE_0 (3): internal drafting data is erroneously referencing another document => Cleaner: Deletion of the link.
  DTE_1 (2): File/Send to Command shows a GhostLink => Cleaner: The link is unset.
  DTE_2 (2) : Text having position link to another text is not up to date after canceling text edition of reference, or Text leader which have Positional Link with a 2D Line is pointed to other element. => Cleaner: Position link is updated to get the correct position.

 

10.- 3D Functional Tolerancing & Annotation:Ir arriba

FTA: Functional Tolerancing & Annotation.

    FTA_1 (1) (*): Some features in TTRS (Technologically and Topologically Related Surface) container are not valid; the TTRS features become invalid because their StartUp has been removed from the container => Cleaner: Deletion of the invalid TTRS features.
  FTA_2 (3): The RGE (Reference Geometrical Elements) feature is not used by any 3D annotations; unused elements (RGE) are present => Cleaner: Deletion of the unused RGE features.
  FTA_3 (3): The TTRS feature is not used by any 3D annotations; unused elements (TTRS) are present => Cleaner: Deletion of the unused TTRS features.
  FTA_4 (3): Deleting FTA annotations do not destroy all Drafting internal entities. => Cleaner: Delete all Drafting annotations which are not pointed by FTA one.
  FTA_5 (1): Ghost link problem appears when opening a document => Cleaner: Delete non aggregated 3D annotations.
  FTA_6 (1): FTA dimension features are abnormally in the Annotation Set => Cleaner: delete invalid drafting annotations and recreate the new topology.
  FTA_7 (3): redundant geometrical element under user surface => Cleaner: Not fixable. Needs a manual correction.
  FTA_8 (2): A problem occurs during CG thread status computation => Cleaner: modify feature attribute value.
  FTA_9 (3) : The FTA geometrical tolerance has invalid status when its 3D display is not consistent with its semantic attribute => Cleaner: Non fixable error.
  FTA_10 (3) : The TTRS object which is utilized by the corrupted view is from the different document. Data filtering of the document can not be possible => Cleaner: Creates a new correct TTRS feature on the axis-system and set it to the corresponding View.
  FTA_11 (2) : File/SendTo” command shows an extra empty line among documents to process => Cleaner: Reset the invalid sequence.
  FTA_12 (3) : No 3D Annotation View has been found for a 3D Annotation => Cleaner: Create a new FTA View and reroot it on FTA 3D Annotation and on associated Drafting View.
  FTA_13 (3) : Trying to create a new semantic Datum Target invalidates the Datum with the diagnostic report as \"target label unicity\" => Cleaner: Remove inconsistent Datum Target without any semantic Datum associated.
  FTA_14 (3) : A dimension of visualization is linked to several dimensions or annotation => Cleaner: Remove the invalid links between the dimension of visualization and the linked dimensions.

11.- SheetMetal:Ir arriba

UPD: Update.

    UPD_1 (2): invalid update stamp => Cleaner: Set update to false.

SHM: SheetMetal.

    SHM_0 (2): element with no activity or no value => Cleaner: Activity is fixed.
  SHM_1 (2): internal BRep Edges features were pointed but not aggregated => Cleaner: Aggregate the involved BRep Edge features.
  SHM_2 (2): Some functionality like CutOut, Hole, ... fail => Cleaner: Changes the invalid cylindrical transformation to a valid one.
  SHM_4 (2) : Some sheetmetal feature has wrong link to sheetmetal parameters => Cleaner: Restore of the link between sheetmetal feature and sheetmetal parameters.

 

12.- Manufacturing:

MFG: Manufacturing (Mecanizado).

    MFG_0 (1): Machining Feature not referenced by an Activity; unused machining feature is not deleted (activities cases) => Cleaner: Deletion of the unused Machining Feature.
  MFG_1 (1): Pattern Definition not referenced by a Pattern Usage; unused pattern definition is not deleted (pattern cases) => Cleaner: Deletion of the unused Pattern Definition.
  MFG_2 (2): Manufacturing Geometry referencing a duplicated body; the body referenced by a manufacturing geometry in SMART NC mode is duplicated => Cleaner: Deletion of duplicated body.
  MFG_3 (1): Toolpath not referenced by an Activity => Cleaner: Deletion of the unused Toolpath.
  MFG_4 (2) : A ghost link appears on a machining resource in File/SendTo command. => Cleaner: Unset the attribute on the machining resource.

 

13.- Knowledge:

KWE: Knowledge.

    KWE_1 (1): knowledge object not aggregated; bad performance when opening a document and an URL points a document through an invalid attribute type => Cleaner: Deletion of the Attribute. If the parameter is pointed by a relation, add object in parameter set; if the object is a relation, add it in the relation set).
  KWE_2 (1): Knowledge Relation in a CATPrtCont points to other documents => Cleaner: The relation is destroyed.
  KWE_3 (2): The output value of a relation is not consistent. After forcing relation evaluation, its value changes => Cleaner: The evaluation is forced.
  KWE_4 (2): A Knowledge Check is broken. "!" information is displayed and an error in the stream involves bad pointing in the Check attributes => Cleaner: The links are restored correctly.
  KWE_5 (2): A parameter external Reference is synchronized but with a wrong value => Cleaner: the value is updated with the good one.
  KWE_8 (3): File/SendTo displays a Ghost link between a parameter and a product => Cleaner: modify parameter by removing invalid link.
  URL_1 (3) (*): Bad performance when opening a document and an URL points a document through an invalid attribute type => Attribute is turned into the correct type.

 

14.- Kinematics:Ir arriba

JNT: Joint.

    JNT_1 (1): One or more kinematics joint axis are corrupted => Cleaner: Deletion of corrupted joint.
  JNT_2 (1): One or more geometries pointed by a kinematics joint are corrupted => Cleaner: Deletion of the corrupted joint.
  JNT_3 (1): Several Mechanism containers exist in the same CATProduct document => Cleaner: Deletion of all Mechanism containers except the first non-empty one.
  JNT_4 (2): Constraints associated to the joints of a mechanism are broken => Cleaner: replace an incorrect pointed geometric element by a correct one.
  JNT_5 (2): A "Point on Curve" Joint simulation is not correct => Cleaner: Internal frames of the joint are updated.

15.- Generic Naming:

GNL: Generic Naming Link.

    GNL_1 (3) (*): BRep feature is pointing at a ghost document => Cleaner: Deletion of link.
  GNL_3 (3) (*): BrpRsur, BrpWire, ... are not aggregated => Cleaner: Deletion of BrpRsur, BrpWire,...

 

16.- New Topological Objects:

FGM: Fat Geometry.

    FGM_1 (3): the size of the CATPart is abnormally huge comparatively to the number of elements. Some vertices have unnecessary geometric data (linked curves / surfaces and some surfaces are over defined (unnecessarily extrapolated) => Cleaner: Removing of unnecessary geometric data, the Part is the same but smaller.
peligro If unextrapolated elements are finally extrapolated, the shape of extrapolation can be different from the original one: the extrapolated part of the element has been "cleaned", and extrapolation can be different, depending on the algorithm that generates it.
peligro If you update the CATPart, this error may re-appear again (after the cleaning rule).

 

17.- SpaceAnalysis:Ir arriba

LIF: Product Lifecycle.

    LIF_6 (1) (*): Dimension which are CATSpecObject_Broken => Cleaner: Deletion of the dimension and measure.
  LIF_15 (1): The "Send to" command shows a ghost link due to invalid measure => Cleaner: removes the input selection of the measure.
  LIF_16 (2): The "Send to" command shows a ghost link due to invalid measure inertia => Cleaner: unsets the attribute selection of the measure inertia.

 

18.- Part Design:

BOL: Operaciones Booleanas.

    BOL_0 (2): Visualization problems due to Boolean between Solid body (old) and hybrid body (new) => Cleaner: Invalid operand body will be moved under the part.
  BOL_1 (2) : Visualization problems due to Boolean between two hybrid (new) bodies => Cleaner: Invalid operand body will be moved under the part.
  BOL_2 (2) : Solid body that contains a Boolean feature is not processed when Part to Part data filtering is done => Cleaner: invalid Boolean feature is deactivated and re-activated.

CPF: Part Design Feature.

    CPF_0 (3): Size of a CATPart abnormally huge comparatively to the number of elements => Cleaner: Delete the Unreferenced BREP features.

DRF: Draft.

    DRF_0 (3): Faces to draft, fix aggregation of Brep Features.  => Cleaner: remove Rsur Features from CGMBody to PartBody.
  DRF_1 (3): The default pulling direction is not compatible in pull dir object and vector.  => Cleaner: The default pulling direction in object and vector is reset.

DVB: Default Value Bags.

    DVB_0 (3): An Applicative Design Table can not be deleted => Cleaner: A Design table link found even when no feature was using it.
  DVB_1 (3) : File / SendTo command displays a GhostLink in the CATPart => Cleaner: The improper attribute "Hole_StandardTable" of DefaultValuesBag is unset.

FIL: Fillet.

    FIL_0 (2): During the edition of a fillet, an error "Internal error in mechanical modeler" is flashed. => Cleaner: Move the PointOnEdge (FilletRadius object containing it) to appropriate the ribbon.

THD: Thread.

    THD_0 (3): A Link between a design table and the standard reference file is not broken => Cleaner: break the link.
  THD_1 (3): Change the value of an external parameter does not lead to the update of Thread Description => Cleaner: force change in value of external parameter.

MIR: Mirror.

    MIR_0(2): One or more than one reference elements kept in Generative Tool for mirroring is lost  => Cleaner: The reference elements kept in Generative Tool are created again.

PAT: Pattern.

    PAT_0 (1): Document can not be updated => Cleaner: Redundant instances in GenerTool of User Pattern are deleted.
  PAT_1 (2) : Some instances of the Rectangular Pattern are lost after a modification (parameters) of the occurrence feature => Cleaner: The wrong located  instances are removed and new instances are created at the right place regarding the pattern grid definition.
  PAT_2 (2) : On selection of one edge / face of a instance of Circular pattern (made of User Pattern), the edge / face of another instance of Circular Pattern also gets selected. => Cleaner: The Confusion point is now ignored during the naming of the instances of User Pattern. This results in correct naming of the instances of Circular Pattern.

FMP: Functional Molded Part.

    FMP_1 (2): The divide part's body thickness will not be up to date when the body thickness is changed => Cleaner: Set shell dependency to match divide.
  FMP_2 (2): Sibling feature will not be up to date when the features parameters are changed => Cleaner: Sibling flags are made consistent with the sibling pointer.
  FMP_4 (2): A functional feature using a "to-shell" length does not correct the track of the shell => Cleaner: Reference is changed according to the correct shape.
  FMP_5 (2): A functional feature using a "to-shell" length does no correct the shell => Cleaner: The Reference is changed to the correct shape.
  FMP_6 (2): A functional feature using body thickness for it "wall" value is not updated when the body thickness is changed => Cleaner: The Reference is changed to the correct parameter.
  FMP_7 (2): A "shell-able" feature does not change "wall" direction when the part's shell properties (wall direction: inward / outward) is changed => Cleaner: The Reference is changed to the correct parameter.
  FMP_8 (2): A functional modifier is trying to modify features from another part => Cleaner: Remove targets (from list) that are not in the same functional body.
  FMP_9 (2) : Not able to update part using force update and part is corrupt => Cleaner: If necessary create shell property feature with zero wall thickness.
  FMP_10 (2) : On modifying limiting element, functional fillet does not get updated => Cleaner: Change the attribute quality. Now limiting element attribute is SP_IN.

DEB: Delete Error Body.

    DEB_0 (2): The File / SendTo command shows a ghost link => Cleaner: Remove improper external attributes "listErrorGeom1 and listErrorGeom2".

PSM: Prisme.

    PSM_0 (2): A Ghost Link appears in File/SendTo command => Cleaner: Restore valid symmetric relation between the first and second limit of a prism.

HOL: Hole.

    HOL_0 (1) : Rule created on R17 level on the Hole's Activity parm does not work correctly. => Cleaner: Rule set on the invalid activity parm of the Hole is copied and set on the valid Activity parm. The rule set on invalid activity parm is then deleted.


19.- PlantShipModeler:

Ir arriba

BST: Backup StartUp.

    BST_0 (3): The Backup StartUp is not declared on Psp Product => Cleaner: The Backup StartUp is declared.

BDR:

    BDR_0 (3): Invalid version of 2D/3D modeling => Cleaner: Upgrade will eliminate direct pointing to schematic functions.

CDC: Cross Document Connection.

    CDC_0 (1): The user will be prompt with error window if an invalid version of cross document connections exists => Cleaner: Use publication to support cross document connections.

SCH: Schematic.

    SCH_0 (3): Mismatched update state on an extension => Cleaner: Update state set to TRUE.
  SCH_1 (3): One of the extremity connector of the route object (that is connected to itself) is not displayed => Cleaner: Find all the branch connections that connect connectors belonging to the same object. Remove those connections. Also remove any unconnected branch connections in a route.

PSP: Plant Ship Modeler.

    PSP_0 (3): Piping or Tubing specification attribute should not be set by the user => Cleaner: Reset the Specification attribute value.
  PSP_1  (2): Wire objects does not have User defined attributes => Cleaner: Update Cable wires with missing user defined attributes.
  PSP_2 (2) : A warning message is displayed advising user to run CATDUA when opening a CATProduct that has some objects with broken derived attributes link => Cleaner: Reset the Derived link for the derived attributes.
  PSP_3 (1) : Ghost links in File/SendTo command from a CATProduct. => Cleaner: Removal of the invalid connection builder connections.
  PSP_4 (2) : Ghost links in File/SendTo command from a Run and its related objects (e.g. Line ID) => Cleaner: Unset the value of the old parameter which has the ghost link and remove it.

 

20.- Equipment and Systems Arrangement:

RSN: System Routing Segments an Nodes.

    RSN_0 (2): File/SendTo displays a Ghost Link => Cleaner: recreate a new parameter and delete the old which has the ghost link.
  RSN_1 (2): File/SendTo displays a Ghost Link => Cleaner: recreate a new parameter and delete the old which has the ghost link.

 

21.- Interoperatividad entre CATIA V4 y CATIA V5:

FS4:

    FS4_1 (3): Some elements should not be in the container => Cleaner: Deletion of Unwanted Extension

 

22.- Electrical:

EHI: Electrical Harness Installation.

    EHI_1(3): Flexible curve attributes are not correctly valuated => Cleaner: Set the flexible curve attributes to correct value.
  EHI_2 (2): The display of the name of electrical harness features is given by Reference Designator attribute value and is not NLS compatible => Cleaner: unset the Reference Designator attribute value for Branch and Bundle Segments.
  EHI_3 (2) (*): Electrical knowledge formula is not visible => Cleaner: all electrical formulas under the geometrical bundle are recreated correctly with the correct formulas.
  EHI_4 (1): Bundle segments lead to twisted configuration if minimum bend radius is smaller than the diameter => Cleaner: The Rib geometrical feature does not handle in standard.
  EHI_5 (2): The branch point positions are not coherent when editing branchable. => Cleaner: Reconnects the bundle segment extremities to the right points.
  EHI_6 (2): When a bundle Segment diameter attribute is changed via the panel, the document doesn't get updated. => Cleaner: Broken relations between Circle Radius and ElecDiameter.
  EHI_7 (2): Ribs or Lofts are in Multi-Branchable but cannot be edited as branchable and cannot be seen as bundle segments in branchable edition. => Cleaner: Reconnects the bundle segment to right branchable
  EHI_8 (1): A bundleSegment is missing in the Spec Tree => Cleaner: Bundle Segment is deleted.
  EHI_9 (1): When expanding the Node of the Multibranchables, any branchable does not have the node for a BundleSegment => Cleaner: The corrupted Branchables are deleted.
  EHI_10 (2): Ghost links appear in File/SendTo command from a CATProduct. => Cleaner: Synchronize the Electrical Device Connector instances' attribute of "_Elec_GeoDefinition": i.e. the value of the reference is reported on the instance.
  EHI_11 (2) : Error occurs when adding or removing a branch point => Cleaner: recreates correct links between branchable and mechanical features.
  EHI_13 (2) : The segment extremity is highlighted at wrong location when selecting a bundle segment or bundle segments are geometrically overlapped inside a branchable => Cleaner: The segment extremities are reconnected to the right geometrical points and the bundle segments are updated.

EDL: Electrical Device Librarian.

    EDL_1 (3) : Electrical part document is modified during the instantiation from catalog => Cleaner: Update the electrical features in the part.
  EDL_2 (2): Broken link appears after replacing a device that is connected to other electrical elements by another one => Cleaner: Publish the unpublished connectors of an electrical connection point.
  EDL_3 (3) : The positionning matrix of an internal splice inside a geometrical harness does not correspond to its 3D visualization => Cleaner: Using the link established between the internal splice and the bundle segment with the defined offset value, the internal splice positionning matrix is calculated and set.
  EDL_4 (2): A Ghost Link appears in File/SendTo command => Cleaner: Synchronizes the Electrical Device Connector instances' attribute of "_Elec_GeoDefinition".
  EDL_5 (2): Certain types of Electrical Devices fail to get routed through => Cleaner: creates a missing connector on all concerned Electrical Device references.
  EDL_6 (2) : A V5 Assembly consisting of an Electrical Device with Electrical Connection Point is not migrable while Migration from V5 to V6. => Cleaner: The useless values in the list which are not pointing to any Feature are deleted.

 

  23.- DMU Fitting

Ir arriba

UFC: Unresolved Fitting Catalog.

    UFC_1 (2): An invalid link on DMU Fitting file appears when using the "Send To" command on a specific CATProcess => Cleaner: deletes the unwanted "Track" container.

SHC: Shuttle Container.

    SHC_1 (3): Performance issue when loading a CATPart => Cleaner: deletes an unwanted "Shuttle" container.

TRC: Track Container.

    TRC_1 (3): The name of an invalid CATProduct appears when using the "Send To" command on a specific CATPart => Cleaner: deletes an unwanted "Track" container.

 

24.- Robotics

IGP: IGriP.

    IGP_1 (1): Not aggregated TagConnectors created on constraint definition are deleted by CATDUA when processing LIF_8 error => Cleaner: Aggregate the floating TagConnectors with the TagGroup it's logical parent.

 

  25.- Mold Design

TFC: Tooling Feature Corruption.

    TFC_0 (2): When opening only a sub-product of a Tooling Assembly some products that are not part of the loaded sub-product are also loaded => Cleaner: The pointing attribute is resetted on the first rank instance of the product.
  TFC_1 (2): A product takes a very long time to be closed => Cleaner: Suppress duplicated links.
  TFC_2 (2): When opening only a sub-product of a Tooling Assembly some products that are not part of the loaded sub-product are also loaded => Cleaner: Resets to 0 all the attributes of the useless extensions (their complete removal is not possible).

 

  26.- Body in White:

    LIF_14 (3): Ghost link pop up when opening a CATProduct => Cleaner: Delete unused Body in White object.
  LIF_17 (3): Ghost link pop up when opening a CATProduct => Cleaner: Unset invalid attribute on the Automotive BiW Fastening feature.
  LIF_18 (3) : Ghost link pop up when opening a CATProduct => Cleaner: Unset invalid attribute on the Automotive BiW Fastening Joint Element feature instance.
  BIW_0 (1) : BIW Joint Body Definition Joined Contact Zones is not updated when BIW Joint Definition is modified => Cleaner: The link between the BIW Joint Body and the BIW Joint is rebuilt.

 

  27.- Camera:

CAM: Camera.

    CAM_2 (1) : Applicative cameras disappear and some ghost links may appear => Cleaner: instanciate a new camera with SpecObject_broken data.

 

  28.- Scene:

SCE: Scene.

    SCE_0 (3): Some ghost links appear in the File/SendTo command => Cleaner: deletion of the useless scene feature.

 

  29.- Technological Result:Ir arriba

TER: Technological Result.

    TER_0 (2): Update status of the Technological Result node does not change when adding/modifying a feature in the body. => Cleaner: RePlug invalid TROutput to the last shape feature (or its ResultOut) of the tool in which it has been created.

  
  30.- Power Copy:

PWC: Power Copy.

    PWC_0 (1): => Cleaner: Deletion of all Power Copies that point to an external document.

  
31.- SFM (Structure Functional Modeler):

SFM: SFM (Structure Functional Modeler).

    SFM_1 (2): Stiffener created via Copy/Paste on new plate is out of date when the original plate is modified => Cleaner: replace the link to the original plate by a link to the plate containing the corrupted stiffener.
  SFM_2 (2) : During instantiation of the beam on curve via Power Copy, the support of the beam is not replaced => Cleaner: Replace the link to the selected curve by a link to the IntDisconnect

 

  32.- PMD (Process Modeler)

PMD: Process Modeler.

    PMD_1 (3) : Some external resources (reference product) in a CATProcess document may not be present in the resource context container => Cleaner: Useless entries in the container are removed and needed entries extracted from the resource list are added to the container.
  PMD_2 (3) : Some external product (reference product) in a CATProcess document may not be present in the product context container. In addition, certain entries in the container may have no corresponding instances under the PPR tree referring to them. => Cleaner: Useless entries in the container are removed and needed entries extracted from the product list are added to the container.

 

  33.- Mechanism

    MEC_1 (1) : When user opens a product containing mechanism and when he opens File/SendTo/Directory, extra components are seen even if model does not have those components => Cleaner: Corrupt imported mechanism is deleted and again imported from reference mechanism. If it is a mechanism at root product level it is simply deleted.

Ir arriba

 

 
©Muchocatia. Todos los derechos reservados
Aviso legal
Política de privacidad
Mapa web
Contacto
contadores
Regreso al contenido | Regreso al menu principal